Microtest OMNIScanner2 User's Guide Page 122
- Page / 133
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
OMNIScanner User Guide
B - 2
OMNI
Scanner
and OMNI
Remote
use a charging mechanism that minimizes
the effects of shallow discharging. To maximize battery life, the battery
temperature is monitored and maintained within limits during the charging
process. Charging under high temperature conditions may result in longer
recharge times or premature termination of charging.
Battery Charging
Charging of the battery is enabled in the OMNI
Scanner
and OMNI
Remote
whenever the AC adapter is plugged in and the units are powered off.
The recharge time is typically 4½ hours to completely charge a fully dis-
charged battery.
Charging is automatically terminated by the units when full capacity or over
temperature conditions are reached. To enhance long term life and capac-
ity of the battery a maintenance and topping charge period starts right after
the rapid charge is completed. The charging status is displayed on both
units. The graphic LCD displays charging status on the OMNI
Scanner
,
while LEDs indicate the status on the OMNI
Remote
unit.
Status conditions are as follows:
• Charge (RED) for OMNI
Remote
low battery status
• Charge (GREEN) while OMNI
Remote
battery is charging
• Charge (GREEN - blinking) when battery is charged
Battery Tips
• Power off the unit before changing the battery pack. Charging is only
enabled when the unit is turned OFF.
• If not on AC power, the battery packs must be replaced within five
minutes to avoid loss of time and date in the OMNIScanner unit.
• If the display goes blank while the AC adapter is plugged into the
Scanner, it indicates that the battery pack is on maintenance
(“trickle”) charge.
• The average time to recharge the battery pack is about 4½ hours.
• To maximize battery pack life, avoid extreme temperatures.
• Using OMNIScanner with the backlight turned ON causes increased
battery drain.
(See Chapter 1 - Introduction: OMNIScanners Keypad:
Backlight)
• Average daily life of the battery pack is about ten hours.
• An external charger is also available. Contact your Microtest distributor
for details on the external charger, Microtest Part Number 8003-01.
- OMNIScanner 1
- Scanner2 2
- Scanner LT 2
- Contents 3
- Chapter 1 - Introduction 7
- OMNIFiber 8
- Tools Software 8
- OMNIScanner’s Display 9
- OMNIScanner’s Keypad 10
- A UTOTES T 11
- OMNIRemote’s LED Indicators 13
- OMNIRemote Keys 13
- When To Use OMNIRemote 14
- OMNIFiber MM LED Indicators 16
- OMNIFiber SM LED Indicators 16
- Editing With OMNIScanner 18
- Editing Alphanumeric Fields 19
- Technical Support 20
- Product Versions 21
- Chapter 2 - Getting Started 23
- Twisted Pair Networks 23
- Preparation 24
- Certification 24
- Completion 24
- Setting the Reference 25
- Project Selection 26
- AUT OTES T 27
- Basic Link 33
- Permanent Link 34
- Chapter 3 - Getting Started 35
- Fiber Optic Networks 35
- Preparing an Autotest 39
- 2 JUMPER METHOD AUTOTEST 39
- 1 JUMPER METHOD AUTOTEST 40
- 3 JUMPER METHOD AUTOTEST 40
- Loopback Autotest using OMNI 41
- Running a Fiber Autotest 42
- Fiber Autotest Results 43
- Chapter 4 - Setup 45
- Set Reference 46
- Autotests 47
- Projects 51
- Editing a Circuit ID 52
- Configurations 54
- Autotest Run Options 54
- Autotest Save Options 55
- User Options 56
- Adapter Usage 57
- Remote Info 57
- Fiber Adapter Info 58
- Format MMC 58
- Regional Settings 58
- Chapter 5 - Measurements 61
- Measuring Fiber Optic Cabling 62
- Measuring Coaxial Cabling 62
- Selecting an individual Test 62
- General Information 63
- 1x 2x 4x 10x 64
- Length/Delay 65
- Attenuation 67
- Return Loss 68
- ACR/Bandwidth 70
- Resistance 71
- Power Sum NEXT 71
- Power Sum ELFEXT 72
- Power Sum ACR 73
- Power Meter 75
- Coax Tests 76
- Tracer/Toner 76
- Chapter 6 - Diagnostics 79
- Wiremap Displays 80
- TDNXT Examples 83
- Using TDRL to Diagnose a Link 86
- TDRL Examples 86
- Impulse Noise 88
- Cable Trace 89
- Office Locator 89
- Scanner 90
- Chapter 7 - Results 91
- Viewing Autotest Results 92
- Establishing the Reference 95
- The Launch/Jumper Cable 96
- The Reference Methods 96
- One Jumper Reference Method 97
- Two Jumper Reference Method 98
- Three Jumper Reference Method 99
- OMNIScanner User Guide 100
- Scanlink 101
- OMNIScanner User Guide 102
- Chapter 11 - MultiMediaCard 105
- MultiMediaCard Maintenance 106
- The MMC Structure 106
- Installing the USB Driver 107
- Physical Characteristics 113
- User Interface 113
- Environmental 114
- Serial Port 114
- Test Functions 116
- Wire Map 116
- High Voltage Input Protection 119
- Rechargeable Battery Pack 121
- AC Connector 121
- Battery Charging 122
- Battery Tips 122
- Criteria 123
- OmniScanner User Guide 124
- Appendix D - Cable Pin-Outs 125
- Cable Pin-Out Signals 126
- Index - 1 127
- Index - 2 128
- Index - 3 129
Related products and manuals for Cable network testers Microtest OMNIScanner2
(61 pages)© 2020, manymanuals.com. All rights reserved. | 1.745 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals