Microtest OMNIScanner2 User's Guide Page 75
- Page / 133
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
5 - 15
OMNIScanner User Guide
Power Meter
The Power Meter function reports the overall received power. Use it to
quickly verify and correct cabling and equipment problems.
The POWER METER screen shows the currently selected wavelength and
light source mode.
The overall power is displayed.
OMNI
Fiber
main is designed to provide a consis-
tent, calibrated light source for effectively measuring
signal loss in fiber optic cables. The transmitted
light can be operated continuously or modulated.
When testing loss, use the continuous light source,
when identifying fiber cables with a tone locator, use
the 2KHz modulated mode.
Press (Continuous) or (Modulated) to change the light
source.
When using OMNIFiber MM (multimode), press or to change
the wavelength of the OMNIFiber Main transmitted and received wave-
lengths.
When using OMNIFiber SM (single-mode), press or to
change the wavelength of the OMNIFiber Main transmitted and received
wavelengths.
Either Main or Remote can be used as the light source with the main power
meter.
When OMNI
Fiber
is attached to OMNI
Remote
, the remote unit can be used
as light source. With the OMNI
Fiber
adapter attached, press the
λλ
λλ
λ key to
activate the light source and provide continuous or modulated light at 850 or
1300 nm for multimode fiber, or at 1310 or 1550 for single-mode fiber. The
green LED of the appropriate wavelength will blink rapidly when modulated
light is transmitted. If the transmitted light is continuous, the green LED will
not blink.
Press to set the reference value, place it in the appropriate field, and
start calculating the loss.
Press ESC to exit the POWER METER screen.
- OMNIScanner 1
- Scanner2 2
- Scanner LT 2
- Contents 3
- Chapter 1 - Introduction 7
- OMNIFiber 8
- Tools Software 8
- OMNIScanner’s Display 9
- OMNIScanner’s Keypad 10
- A UTOTES T 11
- OMNIRemote’s LED Indicators 13
- OMNIRemote Keys 13
- When To Use OMNIRemote 14
- OMNIFiber MM LED Indicators 16
- OMNIFiber SM LED Indicators 16
- Editing With OMNIScanner 18
- Editing Alphanumeric Fields 19
- Technical Support 20
- Product Versions 21
- Chapter 2 - Getting Started 23
- Twisted Pair Networks 23
- Preparation 24
- Certification 24
- Completion 24
- Setting the Reference 25
- Project Selection 26
- AUT OTES T 27
- Basic Link 33
- Permanent Link 34
- Chapter 3 - Getting Started 35
- Fiber Optic Networks 35
- Preparing an Autotest 39
- 2 JUMPER METHOD AUTOTEST 39
- 1 JUMPER METHOD AUTOTEST 40
- 3 JUMPER METHOD AUTOTEST 40
- Loopback Autotest using OMNI 41
- Running a Fiber Autotest 42
- Fiber Autotest Results 43
- Chapter 4 - Setup 45
- Set Reference 46
- Autotests 47
- Projects 51
- Editing a Circuit ID 52
- Configurations 54
- Autotest Run Options 54
- Autotest Save Options 55
- User Options 56
- Adapter Usage 57
- Remote Info 57
- Fiber Adapter Info 58
- Format MMC 58
- Regional Settings 58
- Chapter 5 - Measurements 61
- Measuring Fiber Optic Cabling 62
- Measuring Coaxial Cabling 62
- Selecting an individual Test 62
- General Information 63
- 1x 2x 4x 10x 64
- Length/Delay 65
- Attenuation 67
- Return Loss 68
- ACR/Bandwidth 70
- Resistance 71
- Power Sum NEXT 71
- Power Sum ELFEXT 72
- Power Sum ACR 73
- Power Meter 75
- Coax Tests 76
- Tracer/Toner 76
- Chapter 6 - Diagnostics 79
- Wiremap Displays 80
- TDNXT Examples 83
- Using TDRL to Diagnose a Link 86
- TDRL Examples 86
- Impulse Noise 88
- Cable Trace 89
- Office Locator 89
- Scanner 90
- Chapter 7 - Results 91
- Viewing Autotest Results 92
- Establishing the Reference 95
- The Launch/Jumper Cable 96
- The Reference Methods 96
- One Jumper Reference Method 97
- Two Jumper Reference Method 98
- Three Jumper Reference Method 99
- OMNIScanner User Guide 100
- Scanlink 101
- OMNIScanner User Guide 102
- Chapter 11 - MultiMediaCard 105
- MultiMediaCard Maintenance 106
- The MMC Structure 106
- Installing the USB Driver 107
- Physical Characteristics 113
- User Interface 113
- Environmental 114
- Serial Port 114
- Test Functions 116
- Wire Map 116
- High Voltage Input Protection 119
- Rechargeable Battery Pack 121
- AC Connector 121
- Battery Charging 122
- Battery Tips 122
- Criteria 123
- OmniScanner User Guide 124
- Appendix D - Cable Pin-Outs 125
- Cable Pin-Out Signals 126
- Index - 1 127
- Index - 2 128
- Index - 3 129
Related products and manuals for Cable network testers Microtest OMNIScanner2
(61 pages)© 2020, manymanuals.com. All rights reserved. | 0.889 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals